Saltar al contenido
Remediación de moho licenciada — llame para agendar
EN
MoldAct logo MoldAct Remediación de Moho Certificada IICRC S520
Common moisture and mold conditions found in an unencapsulated crawl space

Encapsulación de Espacio de Rastreo en Wynwood

La encapsulación del espacio de rastreo instala una barrera de vapor de polietileno grueso para sellar el suelo y las paredes, controlar la humedad, y prevenir el crecimiento futuro de moho — una solución permanente para espacios de rastreo húmedos.

Llamar (877) 660-0430 Inspección Gratis

Obtenga su Inspección de Moho Gratis

O llame ahora: (877) 660-0430

Encapsulación en Wynwood: lo que debe saber

Wynwood's industrial and warehouse buildings — many repurposed as art galleries, studios, and mixed-use spaces — have flat roofs and minimal insulation that create extreme attic and roof-deck heat and humidity, driving rapid mold growth after any roof membrane failure.

The neighbourhood's rapid gentrification has produced many renovation projects in buildings not remediated after historic flooding — mold discovered during demolition is common in older Wynwood industrial stock.

Condiciones de moho en Wynwood

Tipos de moho comunes en esta zona: Aspergillus/Penicillium (flat-roof building interiors); Cladosporium (warehouse and studio interiors); Stachybotrys (unremediated historic flooding in older buildings).

Señales de que necesita encapsulación

  • Mold has been remediated in the crawl space and a permanent moisture solution is needed
  • Humidity in the crawl space consistently above 60% RH
  • Standing water or saturated soil after rain events
  • Visible condensation on crawl-space framing in summer
  • Musty odour rising from the floor above the crawl space
  • Previous crawl-space mold that has recurred after treatment
Simple, transparent process

Nuestro Proceso de Encapsulación de Espacio de Rastreo en Wynwood

  1. 1

    Pre-encapsulation assessment

    The crawl space is assessed for standing water, drainage issues, existing mold, and structural concerns. Any mold remediation must be completed and cleared before encapsulation. Active water infiltration must be addressed with drainage or waterproofing before the barrier is installed.

  2. 2

    Surface preparation

    Existing debris, old vapour barriers, and damaged insulation are removed. The soil surface is graded to promote drainage toward the sump crock if present. Foundation walls are cleaned and checked for cracks.

  3. 3

    Vapour barrier installation

    A 20-mil reinforced polyethylene barrier is cut to fit the crawl-space floor and overlapped at all seams by at least 12 inches, with seams sealed with butyl tape. The barrier is extended 6–12 inches up the foundation walls and secured with mechanical fasteners and sealant.

  4. 4

    Foundation wall coverage

    The vapour barrier is attached to the foundation wall to the rim joist level and sealed at all penetrations (pipes, wiring, columns). This prevents warm exterior air and ground moisture from entering at the perimeter.

  5. 5

    Dehumidifier installation

    A commercial-grade dehumidifier with automatic drainage is installed in the encapsulated crawl space to maintain RH below 55%. The dehumidifier is sized for the volume of the crawl space and the local climate moisture load.

Encapsulación de Espacio de Rastreo en Wynwood — Preguntas Frecuentes

¿Proporcionan encapsulación en Wynwood?

Sí — MoldAct proporciona encapsulación en Wynwood (códigos postales: 33127). Llámenos para programar la cita disponible más cercana.

How long does crawl space encapsulation last?

A properly installed 20-mil reinforced vapour barrier lasts 20–25 years with minimal maintenance. Dehumidifiers typically require filter cleaning every 1–3 months and compressor service every 5–7 years.

Does encapsulation replace my sump pump?

No — if the crawl space has groundwater intrusion, a sump system is required to manage active water before encapsulation. Encapsulation controls vapour moisture; it does not manage liquid water infiltration.

What is the difference between a vapour barrier and encapsulation?

A vapour barrier is a thin poly sheet (typically 6-mil) placed on the crawl-space floor. Encapsulation is a full system: heavier barrier (20-mil), wall coverage to rim joist, sealed seams, and mechanical dehumidification — a sealed, conditioned environment rather than a barrier alone.

Encapsulación de Espacio de Rastreo en Wynwood — reserve hoy

Contratistas de remediación de moho certificados IICRC. Llame para agendar.

Llamar (877) 660-0430 Inspección Gratis
Llamar Cotización